![]() |
Kinetis SDK Demo Applications User Guide
1.0.0-beta
Freescale Semiconductor, Inc.
|
| A demo application demonstrates ADC period sample triggered by PIT | |
| Introduction of the ADC Period Sample demo application | |
| User guide on how to customize this application for different configurations | |
| This demo application is a DSPI & eDMA demonstration program | |
| Introduction and the function/definition comments of this demo | |
| User guide on how to use this demo | |
| Flash Demo | |
| Demo application which uses flash Standard Software Drivers (SSD) to erase and program flash regions, and perform swap | |
| The flash_demo application can run from either internal RAM or Flash and uses the Standard Software Drivers (SSD) to erase and program different regions of flash, and run swap if supported on the device | |
| FlexCAN Demo | |
| Introduction and the function/definition comments of this demo | |
| User guide on how to use this demo | |
| This demo Flextimer PWM application | |
| Introduction and the function/configuration of Flextimer PWM | |
| User Guide on how to use the Flextimer PWM applications | |
| This demo application uses GPIO to simulate an I2C to access mma8451 | |
| Introduction and the function/configuration of GPIO I2C functions | |
| User guide on how to use GPIO I2C | |
| This section describes the GPIO UART demo application. The GPIO_UART application simply implements a bit-banged UART terminal application | |
| This section provides brief getting started introductory information | |
| This section provides more detailed information on using this demo application | |
| This demo application simply prints "Hello World" to the terminal and then echoes characters input to the terminal | |
| Introduction and the function/configuration of the hello_world demo application | |
| User guide on how to use the hello_world application | |
| This demo I2C communication application | |
| Introduction and the function/configuration of the I2C master/slave communication | |
| User Guide on how to use the I2C communication applications | |
| This demo application simulates an I2C DAC | |
| Introduction and the function/configuration of the I2C DAC slave and master serial terminals | |
| User guide on how to use the I2C DAC master and slave applications and how to copy it | |
| This demo is a I2C commnication application running on different RTOS | |
| Introduction and the configuration of the I2C master/slave demo with RTOS support | |
| User Guide on how to use the I2C demo with RTOS | |
| This demo application simply turn on a red LED if temperature rise above average or turn on a blue one if temperature drops below average | |
| Introduction and the function/configuration of the LowPower_ADC demo application | |
| User guide on how to use the LowPower_ADC application | |
| A demo application demonstrates different low power modes | |
| Introduction of the low power demo application | |
| User guide on how to execute this application and console setup etc | |
| RTC demo | |
| Introduction and the function/definition comments of this demo | |
| User guide on how to use this demo | |
| This demo application demonstrates RTC basic functions | |
| Introduction of the RTC Functions demo application | |
| User guide on how to use RTC Function Demo application | |
| This demo application is an audio waveform modulation demonstration program | |
| Introduction and the function/definition comments of this demo | |
| User guide on how to use this demo | |
| Play Windows PCM wave file through SAI bus | |
| Introduction and the function/definition comments of this demo | |
| User guide on how to use this demo | |
| A demo application demonstrates shell system in apps/utilities folder | |
| Introduction of the Shell Test Demo application | |
| User guide on how to customize this application for different configurations | |
| SPI Flash access application | |
| Introduction and the function/configuration of SPI Flash functions | |
| User guide on how to use SPI Flash Demo | |
| A demo application demonstrates watchdog signal interrupt and reset when timeout | |
| Introduction of the Watchdog Timer demo application | |
| User guide on how to use this application |